Dyno Results
Vital Statistics
  • Vehicle / Motor
  • Dyno Type
  • Dyno Correction
  • Download Dyno Files
  • Boost Log
BMW E9x M3 (S65 Motor)
Dynojet
STP / STD
Download-1
Boost pressure (7.70 PSI) verified with boost log.
Configuration / Modifications:
  • Active Autowerke Supercharger Stage-2+ w/ Water Meth @ 7.70 PSI Boost
  • Methanol Injection
  • 200 Cell High-Flow Catalytic Converter
  • Akrapovic Evolution Exhaust System (Titanium)
  • 91 Octane (US), 95 Octane (RON)
  • 6-Speed Manual Transmission
Measured Results:
  • Torque
  • Horsepower
343 FT/LBS
478 HP
@ 6250 RPM
@ 8000 RPM
(465.0 NM)
(484.6 PS)
(47.42 KGM)
(356.5 KW)
Dyno Graphs:
The baseline dyno chart is not from this same vehicle. The baseline was taken from a 2011 BMW M3 ZCP with DCT. This baseline was taken on the same dyno under near-identical weather and density-altitude conditions. The DCT typically shows +15whp difference over the 6MT on the same dyno. Subtract 15whp from the baseline for a good approximation of what a 6MT would have as a baseline on this same dyno.
Alternate Images:
All Dyno Runs
Boost and AFR for all runs
Videos:
Other images:
Boost Log Analysis: 7.70 PSI Average, 9.43 PSI Peak
 

Car and Modifications:

  • 2008 BMW M3
  • Active Autowerke Stage-2 Supercharger
  • +Methanol Injection
  • 6MT
  • Akrapovic Evolution Exhaust
  • 91 Octane

Conditions:

  • Temparature:: 72.92 degrees F
  • Atmospheric pressure: 30.09 inHg
  • Humidity: 28%
  • SAE Correction: 0.97
  • STD Correction: 1.00
  • Uncorrected: 1.00

Results:

  • SAE Corrected: 465whp @ 8000 RPM, 334wtq @ 6250 RPM. 7.80 PSI
  • STD Corrected: 478whp, 343wtq
  • Uncorrected: 479whp, 344wtq

Dyno Database:

Dyno Testing Procedures:

These procedures were specified by Active Autowerke.  Since we were on 91 octane, methanol injection must be used.  We originally intended to conduct tests with and without methanol injection, but were advised not to do so without 93 octane gasoline.  We were instructed to run the dyno and let the car cool down one minute between runs.  At the end of three runs, we were instructed to turn off the motor, let the engine cool for ten minutes, then repeat the same testing procedure for three more runs.

In addition to capturing horsepower, torque, and engine RPM, we originally intended to collect spark advance, and knock sensor data from the OBD port via the Bavarian Technic scan tool (with thanks to Bren @ Bren Tuning for providing the necessary configuration file).  However, once we hooked up the BT tool to the OBD port, we discovered we could not read any data from the OBD port using the BT tool.  We did not try to diagnose the problem since we were "on the clock" at the dyno shop.  We later found out this was caused by the Akrapovic Delete-R installed in the system.  We were therefore unable to capture any spark or knock sensor data.  If time permits, we plan to return to the dyno with the same configuration, remove the Delete-R and re-test.

All of the dyno runs are filmed in HiDef video to document the authenticity and independence of the tests.  A Kestral 4500 portable weather station is brought to take independent weather measurements.  This provides a cross-check for the dyno weather station to ensure that the dyno weather station is reading accurately and has not been tampered or altered in any way.

Individual Dyno Results:

Individual dyno results are shown below.  SAE corrected results are shown twice, using two different sources.  The first source (djc) are the SAE corrected results straight from the Dynojet.  The second source (sae) of SAE corrected results are obtained by using the Kestral 4500 weather station data for each individual dyno run and running it through an independent SAE correction formula.  This ensures that the dyno results are accurate and can be independently audited and verified for authenticity and accuracy.

The legend below has the following meaning:

  • Dyno Run:  Dyno run file
  • Boost Avg:  Boost calculated using trend line.  This is the "official" boost for this dyno run.
  • Boost Peak:  Peak boost observed on this dyno run.
  • Temp(F) = Temperature (Farenheit)
  • RelH = Relative Humidity
  • Pressure(Hg) = Barometric Pressure
  • DA(ft) = Density Altitude
  • WHP(unc) = Uncorrected wheel horsepower
  • WTQ(unc) = Uncorrected wheel torque
  • WHP(djc) = Dynojet SAE corrected wheel horsepower (SAE-1340 PRE-2004)
  • WTQ(djc) = Dynojet corrected wheel torque (SAE-1349 PRE-2004)
  • WHP(sae) = SAE-Adapted wheel horsepower (SAE-1349 2004+)
  • WTQ(sae) = SAE-Adapted wheel torque (SAE-1349 2004+)

 

Dyno Run Boost Avg. Boost Peak Temp(F) RelH Press(Hg) DA(ft) WHP(unc) WTQ(unc) WHP(djc) WTQ(djc) WHP(sae) WTQ(sae)
RunFile_002 7.80 PSI 7.87 PSI 62.0 68.8 29.95 330 476 340 463.17 330.67 462.18 330.13
RunFile_003 7.80 PSI 8.14 PSI 62.9 68.5 29.95 392 468 339 455.99 330.34 455.07 329.63
RunFile_004 7.40 PSI 9.39 PSI 62.5 69.4 29.95 366 472 331 460.70 323.02 458.74 321.70
RunFile_005* 7.80 PSI 9.43 PSI 62.1 70.5 29.95 337 479 344 465.19 334.01 465.36 334.20
RunFile_006 7.60 PSI 7.53 PSI 63.2 69.2 29.95 411 473 335 461.01 326.46 460.24 325.96
RunFile_007 7.80 PSI 9.27 PSI 63.5 66.2 29.95 428 463 332 451.86 323.70 450.42 322.98

* Entry used for the Dyno Database

Methods for calculating average boost:

  • Export Uncorrected dyno data to Microsoft Excel spreadsheet.  Export a sample very 50 RPMs.
  • Note RPM of Max Horsepower.  This value will be used to graph boost.
  • Create scatter X-Y plot in Excel with Boost on the Y-Axis, and RPM on the X-Axis.  The range of this graph will start at the first sample, and end at the exact location of MaxHP mentioned in the previous step.  If MaxHP was found at 8150 RPMs, then only graph boost, HP, and RPM up to 8150 RPMs.  This is very important to follow these steps.  Extending RPMs beyond the location of MaxHP will influence the average boost, usually by making it higher than it should be.
  • Use the mouse to highlight the boost graph just created.  Right click and select "add Trendline"
  • Select "Linear" trendline method.
  • The data, graph, and spreadsheet used in this DynoDB entry is included in the "Dyno Files" download link at the top of this page.  Use it as an example for creating your own boost log if desired.

Notes about Dyno Boost Log:

The boost in this entry looks a little irregular; it seems to waver quite a bit.  As more results are provided from this dyno, the boost data will regularly be monitored for accuracy.  If the results are found to be inaccurate, then the entry in the Dyno Database will be adjusted accordingly -- up or down -- depending on the results of newer analysis.

Notes about Baseline Vehicle:

The baseline dyno chart is not from this same vehicle. The baseline was taken from a 2011 BMW M3 ZCP with DCT. This baseline was taken on the same dyno under near-identical weather and density-altitude conditions. The DCT typically shows +15whp difference over the 6MT on the same dyno. Subtract 15whp from the baseline for a good approximation of what a 6MT would have as a baseline on this same dyno.